Not far from the village, the water was released and the real old fish skeleton team was sent to the market, and the Niushan Town Woodworks Factory finally got this precious cube of sugar maple.

They knew that they had been much behind a long time ago. After getting the wooden square, they did not dare to delay for a minute. They immediately summoned everyone to start studying the fast wood.

Because time is very tight, it is too late to dry first and then deal with it. Director Hu plans to take two steps to break the huge square wood and cut it into two squares.

Take one piece to dry, start processing the other piece now, try various processing methods, and try drying after processing.

However, this kind of precious wood cannot be cut casually. Some expensive wood, even more expensive than gold, can cause a little more loss during the production process, which can make people feel pain.

Director Hu didn't dare to be too big, so he went into the battle himself, measured the size of the wood, and then drew a cutting line. Then they replaced the clean band saw with imported ultra-fine and ultra-thin saws, so that the master with the best skills in the factory would take action and start to break the big material.

The band saw rotated at high speed, and even some traditional hardwoods were as fragile as foam when they came to the band saw. The master set up the guide rails, rulers and limiters, and firmly grasped the wooden square with both hands and steadily approached the wooden square.

As soon as the band saw came into contact with Mu Fang, I heard a "squeaking" sound.

"Oh, this sound is wrong!" The master subconsciously pulled Mu Fang back, then closed the band saw, and then looked at the saw blade and suddenly burst into a cold sweat: "Luckily it was closed early!"

"What's going on?" Director Hu also came forward and saw that the originally fine saw teeth were missing. It was a few thousand yuan per piece and was said to be able to even saw steel. It was almost worn out.

"What's going on? Did we get the wrong saw blade?"

"It's not wrong, it's the imported saw blade we bought last time, that's right." The master turned his head to look at the wooden square and saw a white line cut out from the wooden square, with small teeth embedded in the white line.

"This is not being smoothed out, it is being stuck!"

What kind of wood can break this ultra-high hardness serrated serrated?

How tough is the fiber of this thing?

"We... look at each other in a different direction?" The master wiped a cold sweat and said, "This time, let's try following the wood grain?"

Just now, I planned to cut the wood horizontally and cut it with vertical wood grain. I didn’t expect that the wood grain of the wood is so strong.

"This may result in more losses..."

"It's better than not being able to cut it. If you can cut it into a plate, you can use a laser cutting machine." said the master.

Director Hu thought for a while and nodded.

Now he didn't care about maximizing the use of materials, so he crossed the wood, replaced it with a band saw, and started the machine again.

The sound of "Squeak!" is much louder than before.

"This sound is right." The master pushed forward steadily with both hands, but the more he pushed forward, the more wrong the sound became. From the beginning, it turned into a buzzing sound.

Two centimeters later, the saw blade was actually clamped by the wood!

"Squirt!"

"The water is spraying..."

"What's going on? How could it be clamped?"

I finally removed the wooden square from the band saw, and the band saw was charred black. It was rubbed carbonized wood, and the master was also confused.

Vertical wood grain will get stuck in the teeth, and will be clamped along the wood grain. What should I do?

Director Hu leaned forward and suddenly wondered: "Hey, where is the white line just now?"

Just now, when cutting vertical wood grain, the band saw once cut a white line on the wood square.

At this time, the white line had faded so much that it was almost invisible.

The master reached out and touched the position of the white line without believing in it, and only touched a few broken teeth stuck inside the band saw, with small triangular teeth sticking to their fingertips.

The white line is completely invisible.

"How is this... possible?" Master and Director Hu looked at each other, then quickly looked at the saw mark that had cut into a centimeter-deep depth along the wood grain.

They saw that the saw mark was recovering at a speed visible to the naked eye, and the silver light seemed to become particularly bright at this time, and a silver line appeared at the saw mark.

After the saw marks were completely restored, the silver light dispersed, and the wooden square became the beginning again.

Flat, smooth, square, beautiful texture.

But the master and Director Hu's hair felt that it was about to stand up.

"This...this wood shouldn't be alive, right?" said the master.

"Even if... even a tree is alive, it cannot grow so fast!" Director Hu said that he had seen Mu Fang in his life, and there were eight thousand or eight thousand, but he had never seen any piece of wood so exaggerated!

What exactly is this?

Isn’t this just a piece of wood? How can it heal itself?

Could this be actually the Cybertron cube?

Or is it a magical alien creature?

No, this is impossible.

However, how can this kind of wooden square that cannot be cut open and heals itself?

"Is this to play with us?" Director Hu almost threw the table.

"No, no... Other companies will always have a solution. Go and inquire about how other companies process this wood." Director Hu said.

Although it is just a small factory, after all, I have been immersed in the wood processing industry for so many years and I still have some connections.

Soon they contacted several companies that also received the order.

When I heard Director Hu ask about the wood, several companies were sloppy at the beginning: "This is a commercial secret. Lao Hu, if I tell you, I would make a mistake."

"Don't you come to those who are weak, can't you cut the wood?"

After saying this, the other party couldn't hold back and immediately complained: "The saw blades we imported were scrapped seven or eight, and the motors were almost burned. After changing them all, I just wanted to pull the big saw with the factory manager. I couldn't cut the wooden square. How should I process the wood that I couldn't cut?"

Another manufacturer said: "Our boss has a familiar metal processing factory. He plans to take this wooden square to try the metal cutting machine at the metal processing factory. We are waiting for news."

After a while, he said again: "Old Chen from the metal processing factory almost knocked out our boss and said that our wooden square had broken their knife heads..."

Metal cutting is mostly done by milling, and the high-speed rotating cutting head is almost wrapped in cocoons by flexible wood fibers.

It was not only Director Hu who asked about the news, but the others were helpless about this piece of wood and were also inquiring about each other. When they heard that others were helpless about this piece of wood, one or two were confused. What should we do?

"By the way... how did this wood be cut into this at the beginning?" Director Hu suddenly said, "It's impossible that this wood will look like this from the beginning!"

Director Hu thought for a long time and called Deng Yali.
Chapter completed!