This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setup program. Set the slave disk parameter item to "none" in the "standard    cmos     features" option to block the slave disk. Set the master disk as the boot hard disk in the "advanced   bios    features" option to set the master disk as the boot hard disk. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

in     9x

Use letter     assigner

letter     assigner can arbitrarily specify the drive letter of the hard disk. Start letter     assigner, and 26 drive letters "a~z" are listed below the toolbar of letter                                                                                                                                                                                                                              �

During the operation, if you need to give up the modification, just execute "Edit → Restore Original" or press the "ctrlz" key combination. Generally, the drive letter of the system disk cannot be modified, otherwise it may cause a system startup error. When modifying the drive letter of the system disk, a prompt window will pop up by letter    assigner. (lanfu)

System Setting Method

indos2000/xp/2003

Modifying the malfunctioning drive letters in indos2000/xp/2003 is very simple. It can be easily done through the system's own "disk management" program. Click "Start → Run" to start "Disk Management". Let's take a look at how to modify the drive letters.

Step 1: As shown in Figure 1, right-click the drive that needs to modify the drive letter and select the "Change drive letter and path" command. When changing the drive letter of the drive, be careful that the drive letter of the system disk cannot be modified and is not allowed to be modified at will, otherwise the system will not be started.

Step 2: Press the "Change Drive Letter and Path" dialog box that pops up, and in the next window, specify a new drive letter (drive letter) for the drive.

Tip: If the drive letter you want to specify has been occupied by another disk partition, you can first modify the disk partition that occupies the drive letter, specify it as another disk letter, and release the drive letter occupied by the disk partition.

indos9x/me

In indos9x/me, you can usually only set the master-slave jumper and bios settings of the hard disk, or use the third-party tool letter    assigner to adjust the hard disk drive letter. We just click the disk partition to change in the program (as shown in Figure 2), then specify the English drive letter on the toolbar, press "File → Save" to save the settings after adjustment, and restart the computer, and then ok. It should be noted that letter     assigner cannot modify the partition where the indos system is located. When you make inappropriate adjustments, letter     assigner will display a warning message to remind you that you must not forcefully modify it at this time. Finally, if you are using a memory emulated hard disk (virtual hard disk), letter       assigner can also specify the virtual disk drive letter by identifying the "ms-ramdrive" disk volume label.

Use partitionmagic

partitionmagic can repartition, format, copy partitioning and other operations on the hard disk. The operation method of using it to modify the drive letter is as follows:

Start partitionmagic, right-click the drive letter that needs to be modified, select "Advanced → Modify drive letter" in the shortcut menu, and then select the new drive letter in the pop-up "Change drive letter" window, click the "OK" button, then select the "General → Apply Change" command, and restart as prompts.

Other:

(1) indos   2000/xp

This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setup program. Set the slave disk parameter item to "none" in the "standard    cmos     features" option to block the slave disk. Set the master disk as the boot hard disk in the "advanced   bios    features" option to set the master disk as the boot hard disk. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

in     9x

Use letter     assigner

letter     assigner can arbitrarily specify the drive letter of the hard disk. Start letter     assigner, and 26 drive letters "a~z" are listed below the toolbar of letter                                                                                                                                                                                                                              �

During the operation, if you need to give up the modification, just execute "Edit → Restore Original" or press the "ctrlz" key combination. Generally, the drive letter of the system disk cannot be modified, otherwise it may cause a system startup error. When modifying the drive letter of the system disk, a prompt window will pop up by letter    assigner. (lanfu)

System Setting Method

indos2000/xp/2003

Modifying the malfunctioning drive letters in indos2000/xp/2003 is very simple. It can be easily done through the system's own "disk management" program. Click "Start → Run" to start "Disk Management". Let's take a look at how to modify the drive letters.

Step 1: As shown in Figure 1, right-click the drive that needs to modify the drive letter and select the "Change drive letter and path" command. When changing the drive letter of the drive, be careful that the drive letter of the system disk cannot be modified and is not allowed to be modified at will, otherwise the system will not be started.

Step 2: Press the "Change Drive Letter and Path" dialog box that pops up, and in the next window, specify a new drive letter (drive letter) for the drive.

Tip: If the drive letter you want to specify has been occupied by another disk partition, you can first modify the disk partition that occupies the drive letter, specify it as another disk letter, and release the drive letter occupied by the disk partition.

indos9x/me

In indos9x/me, you can usually only set the master-slave jumper and bios settings of the hard disk, or use the third-party tool letter    assigner to adjust the hard disk drive letter. We just click the disk partition to change in the program (as shown in Figure 2), then specify the English drive letter on the toolbar, press "File → Save" to save the settings after adjustment, and restart the computer, and then ok. It should be noted that letter     assigner cannot modify the partition where the indos system is located. When you make inappropriate adjustments, letter     assigner will display a warning message to remind you that you must not forcefully modify it at this time. Finally, if you are using a memory emulated hard disk (virtual hard disk), letter       assigner can also specify the virtual disk drive letter by identifying the "ms-ramdrive" disk volume label.

Use partitionmagic

partitionmagic can repartition, format, copy partitioning and other operations on the hard disk. The operation method of using it to modify the drive letter is as follows:

Start partitionmagic, right-click the drive letter that needs to be modified, select "Advanced → Modify drive letter" in the shortcut menu, and then select the new drive letter in the pop-up "Change drive letter" window, click the "OK" button, then select the "General → Apply Change" command, and restart as prompts.

Other:

(1) indos   2000/xp

indos     2000/xp generally does not cause the problem of crossing the drive letters, but the premise is that indos    2000, only one hard disk is installed when installing xp, and the second hard disk can only be hung after the installation is completed. If indos    2000/xp is installed after adding the second hard disk, the crossing will still occur, and this is permanent, and even if you remove the second hard disk, it will be useless.

However, we can enter the "Control Panel → Administrative Tools → Computer Management" window, select "Disk Management" under "Computer Management", select the corresponding partition, execute the "Change Drive Name and Path" command from the right-click menu, click the "Change" button in the dialog box of Figure 1, then reassign a drive letter, and then repeat the command for other partitions.

(2) indos   9x/me    This *** book starts with ****** and posts on the first ****** ***.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setup program. Set the slave disk parameter item to "none" in the "standard    cmos     features" option to block the slave disk. Set the master disk as the boot hard disk in the "advanced   bios    features" option to set the master disk as the boot hard disk. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

in     9x

Use letter     assigner

letter     assigner can arbitrarily specify the drive letter of the hard disk. Start letter     assigner, and 26 drive letters "a~z" are listed below the toolbar of letter                                                                                                                                                                                                                              �

During the operation, if you need to give up the modification, just execute "Edit → Restore Original" or press the "ctrlz" key combination. Generally, the drive letter of the system disk cannot be modified, otherwise it may cause a system startup error. When modifying the drive letter of the system disk, a prompt window will pop up by letter    assigner. (lanfu)

System Setting Method

indos2000/xp/2003

Modifying the malfunctioning drive letters in indos2000/xp/2003 is very simple. It can be easily done through the system's own "disk management" program. Click "Start → Run" to start "Disk Management". Let's take a look at how to modify the drive letters.

Step 1: As shown in Figure 1, right-click the drive that needs to modify the drive letter and select the "Change drive letter and path" command. When changing the drive letter of the drive, be careful that the drive letter of the system disk cannot be modified and is not allowed to be modified at will, otherwise the system will not be started.

Step 2: Press the "Change Drive Letter and Path" dialog box that pops up, and in the next window, specify a new drive letter (drive letter) for the drive.

Tip: If the drive letter you want to specify has been occupied by another disk partition, you can first modify the disk partition that occupies the drive letter, specify it as another disk letter, and release the drive letter occupied by the disk partition.

indos9x/me

In indos9x/me, you can usually only set the master-slave jumper and bios settings of the hard disk, or use the third-party tool letter    assigner to adjust the hard disk drive letter. We just click the disk partition to change in the program (as shown in Figure 2), then specify the English drive letter on the toolbar, press "File → Save" to save the settings after adjustment, and restart the computer, and then ok. It should be noted that letter     assigner cannot modify the partition where the indos system is located. When you make inappropriate adjustments, letter     assigner will display a warning message to remind you that you must not forcefully modify it at this time. Finally, if you are using a memory emulated hard disk (virtual hard disk), letter       assigner can also specify the virtual disk drive letter by identifying the "ms-ramdrive" disk volume label.

Use partitionmagic

partitionmagic can repartition, format, copy partitioning and other operations on the hard disk. The operation method of using it to modify the drive letter is as follows:

Start partitionmagic, right-click the drive letter that needs to be modified, select "Advanced → Modify drive letter" in the shortcut menu, and then select the new drive letter in the pop-up "Change drive letter" window, click the "OK" button, then select the "General → Apply Change" command, and restart as prompts.

Block the slave disk. Set the master disk to boot the hard disk in the "advanced    bios    features" option. Save the settings and restart it, the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method
Chapter completed!